How to Fix a Malfunctioning of GE Electric Stove Burner Not Working?

GE electric stove burners consist of a metal coil housed in a housing composed of porcelain or stainless steel. However, they can be damaged and malfunction. There are a few reasons for a GE electric stove burner not working.

These are wire connection fault, damaged burner element, faulty surface element switch, control board issue, inefficient power, damaged infinity switch, and malfunctioning temperature sensor.

Key Takeaway

7 Reasons Why Your GE Electric Stove Burner Is Not Working

Here are the reasons and solutions for the GE electric stove burner not working:

Reasons	Solutions
Wire Connection Fault	Fix the damaged wires.
Damaged Burner Element	Replace the burner element.
Faulty Surface Element Switch	Test and change the faulty surface element switch.
Control Board Issue	Install a new control board.
Inefficient Power	Follow the given steps.
Damaged Infinity Switch	Attach a new infinity switch.
Malfunctioning Temperature Sensor	Change the sensor.

1. Wire Connection Fault

You can find the GE electric stove burner’s electrical connections beneath the cooktop. These connections may burn or come loose with time as a result of heat or vibration. 

This problem can also be brought on by general wear and tear. You may experience sporadic or whole power outages due to a loose cable connection.

A burned wire connection may result in resistance. As a result, the burner element cannot heat up correctly.

The Fix:

You will need to turn off the stove’s electricity to repair a loose or burned wire connection. Next, take out the cooktop. You will now have access to the burner’s electrical connections.

Now, you should use a screwdriver to tighten the loose wire connection. You must cut out the burned section of the wire if the wire connection is burned. After that, remove the insulation from the wire ends.

You will need to crimp on new wire connections after the wires have been stripped. After reconnecting the wires to the burner, reinstall the cooktop.

2. Damaged Burner Element

The metal coil that heats up to cook food is called the burner element. It can be harmed by physical force or heat. The burner element won’t be able to heat up correctly if it is broken.

The burner’s element may be harmed if you operate it at an excessively high temperature for an extended time. The burner element will also eventually deteriorate due to wear and tear over time.

Your GE electric stove burner’s element may sustain damage if you drop it or if it is struck by a hard object.

The Fix:

If the burner element is malfunctioning, you must replace it. You must take the cooktop apart to replace the burner element. Just undo the screws holding the burner element in place to remove it.

You can swap out the burner element for a new one after removing the old one. Make sure that you put the replacement burner element in the same position as the previous one.

You can put the cooktop back in place after installing the new burner element. Make sure the burner is operating correctly by giving it a test.

3. Faulty Surface Element Switch

The electrical switch that regulates the power to the burner element is known as the surface element switch. It can fail due to normal wear and tear or a power spike.

If the surface element switch fails, no power is sent to the burner element. So, the burner does not heat up. 

The burner may also not turn on or may not turn off properly. When you try to switch on the burner, you may also hear a clicking sound.

The Fix:

Be sure to follow these guidelines if your surface element is faulty:

• First, remove the cooktop.
• Then, you have to remove the surface element switch.
• Simply loosen the screws that hold it together.
• Replace the surface element switch after it has been removed.
• Make sure to use a compatible one by consulting the user handbook. 
• You must now reassemble and test the GE electric stove burner.

4. Control Board Issue

The electronic circuit board that regulates all of the functions of the GE electric stove burner is known as the control board. It may fail as a result of a power surge.

You may also spot a flaw in the circuit board itself. If the control board fails, electricity may not be sent to the burner element. It may also be unable to regulate the temperature of the burner element.

The Fix:

If a malfunctioning control board is causing your GE electric stove burner to malfunction, you must replace it. The control board must be removed to be replaced. Then, remove the screws that keep it together.

After removing the control board, you can replace it with a new one. If you are unsure about solving the issue, you must contact a qualified appliance repair technician.

5. Inefficient Power

Electric stove burners from GE require a lot of power to function. The burners may not function properly if the stove does not receive adequate power.

It’s possible that the burners aren’t heating up at all. They may not always heat up evenly. You may also notice other electrical issues such as lights dimming or flickering.

This issue could potentially be caused by a problem with the electrical outlet. There could also be an issue with the wiring to the stove.

The Fix:

If you think that a lack of electricity is causing your GE electric stove burner to malfunction, try the following:

• Examine the electrical outlet into which the stove is plugged.
• Check that the outlet is operating properly and that the stove is completely plugged in.
• Examine the wiring to the stove. Check that the wiring is in good condition and that it is correctly linked to the stove.
• If you have additional appliances plugged into the same circuit as the stove, try unplugging some of them to see if that helps.
• If the stove continues to be underpowered, you may need to hire an electrician to establish a dedicated circuit for the stove.

6. Damaged Infinity Switch

On certain GE stoves, the infinity switch is an electrical switch that regulates the power to the radiant burners. It may malfunction as a result of a power surge or normal wear and tear.

The radiant burners won’t be able to turn on if the infinity switch is broken. Sometimes, the radiant burners won’t turn on at all.

They may also fail to shut off correctly. Additionally, when you attempt to switch on the burners, you might hear a clicking sound.

The Fix:

You will have to replace an infinite switch if it is damaged. The procedures for changing a broken infinity switch are as follows:

• Turn off the stove’s electricity.
• Take the cooktop off.
• Find the infinity switch. It is close to the radiant burners under the cooktop.
• Take off the screws securing the infinity switch.
• Cut the cables that are connected to the infinity switch.
• Put the new infinity switch in place. The cables should be connected to the new infinity switch in the same manner as they were to the previous one.
• The screws hold the infinity switch firmly in place.
• Replug the cooktop back in and reconnect the stove’s power supply.

Related Post: Having Frigidaire Stove Electric Oven Issues? Here Is How to Fix It

7. Malfunctioning Temperature Sensor

The temperature sensor of the GE electric stove burner keeps a reading by monitoring the burner element’s temperature. Something wrong with the sensor itself might cause it to fail.

The control board may not get accurate temperature data from the temperature sensor if it is malfunctioning.

The burner may overheat or fail to reach the appropriate temperature. You may also notice that the control board display is showing error warnings.

The Fix:

To fix a malfunctioning temperature sensor:

• Take off the cooktop.
• Find where the temperature sensor is. You can find it within the burner element.
• Take out the temperature sensor. Remove the screw holding it in place to accomplish this.
• Using the screw to secure it, install a new temperature sensor in the same location as the previous one.
• Reinstall the cooktop in the original location.

Related Post: How to Diagnose and Fix: General Electric Stove Problems

Frequently Asked Questions – FAQs