Dishwashers are invaluable appliances that save us time and energy, allowing us to focus on more enjoyable tasks instead of scrubbing dishes.
However, when they malfunction, the convenience can quickly turn into frustration. Fortunately, a simple reset can fix many common issues with your Maytag dishwasher.
In this article, we’ll provide you with a step-by-step guide on how to reset a Maytag dishwasher and help you troubleshoot some common problems.
Why You Might Need to Reset Your Maytag Dishwasher?
Just like any other electronic device, dishwashers may occasionally require a reset to function properly.
Various factors, including power surges, communication glitches between the control panel and the appliance’s components, or even activation of Demo Mode, can lead to issues.
This is where resetting your dishwasher helps to purge all these faults from the air and enable your appliance to run as usual.
Step-by-Step Guide to Resetting Your Maytag Dishwasher
Performing a Factory Reset
A factory reset might seem intimidating, but it’s actually a simple, harmless process that can resolve most issues without needing professional help.
Follow these steps to restore your dishwasher to its default settings:
Step 1: Open and close the dishwasher door to clear any stuck commands in the control board.
Step 2: Press the ‘Rinse’ button five times quickly.
Step 3: Turn off Demo Mode by pressing the ‘Drain/Off’ button twice if it’s on.
Step 4: Finish the reset. Your dishwasher now returns to default settings and accepts new commands.
If problems persist after the reset, contact a qualified Maytag technician to check for possible hardware issues.
Resetting Blinking Lights
Blinking lights usually mean the control panel has a fault or that Demo Mode is active. In newer models, Demo Mode prevents the dishwasher from running cycles. If the control panel lights keep blinking, try these steps:
Step 1: Open and close the dishwasher door.
Step 2: Press the ‘Rinse’ button five times quickly.
Step 3: Press the ‘Drain/Off’ button twice to reset the system.
Step 4: If blinking continues, unplug the appliance for 60 seconds and plug it back in.
Resetting the Control Panel
The control panel is essential for your dishwasher to operate correctly.
If it stops responding, use these steps to reset it:
Step 1: Unplug the dishwasher from the power source for about 15 minutes.
Step 2: After 15 minutes, plug the appliance back in.
Step 3: Press any three buttons in quick succession to refresh the control panel.
Step 4: Repeat these steps if necessary to ensure the control panel responds correctly.
Resetting the Control Lock
If the control panel lights up but the dishwasher doesn’t respond, the Control Lock feature may be active. Disable it as follows:
Step 1: Press the ‘Start/Resume’ button. Alternatively, hold down the ‘Cancel’ or ‘Lock’ button for four seconds.
Step 2: If you mistakenly triggered the control lock, open and close the door to switch it off.
Resetting the Cycle
Step 1: Unplug the dishwasher from the power source for at least 60 seconds.
Step 2: Press the ‘Heated Dry’ button, followed by the ‘Normal’ button.
Step 3: Press both buttons again, then close the dishwasher door to complete the cycle reset.
Clearing error codes
Follow these steps to clear error codes:
Step 1: Check the error code meaning to make sure it doesn’t indicate a serious issue.
Step 2: Unplug the dishwasher for more than 60 seconds to reset the control board and clear faulty codes.
Step 3: Plug the dishwasher back in and check if the error code has cleared.
Maytag MDB8959AWS5 Dishwasher Reset Sequence
Step 1: To reset a Maytag MDB8959AWS5 model, use the following steps to enter diagnostic mode:
Step 2: Open the door and leave it unlatched.
Step 3: Press the buttons in this sequence:
- High-Temp Wash
- Heat Dry
- High-Temp Wash (again)
- Heat Dry (again)
Step 4: Close the door. The dishwasher will run in diagnostic mode for a few minutes and reset for regular use.
Maytag 300 Series Dishwasher Reset
For the Maytag 300 series models:
Step 1: Open the door and leave it unlatched.
Step 2: Press the following buttons in this order:
- Heated Dry
- Normal
- Heated Dry (again)
- Normal (again)
Step 3: Close the door, and wait a few minutes for the reset to complete.
Maytag MDB7749AWB2 dishwasher reset
To reset the MDB7749AWB2 model:
Step 1: Turn off the power source or the circuit breaker and wait at least five minutes.
Step 2: While the door is still open, restore power by plugging it back in or turning on the breaker.
Step 3: Within 8 seconds, press ‘Heated Dry’ six times, then press ‘Start’. Wait while the dishwasher enters diagnostic mode and performs a self-check before returning to regular operation.
Resetting the Maytag Quiet Series 200 dishwasher
To reset a Maytag Quiet Series 200 dishwasher:
Step 1: Unplug the dishwasher or disconnect it from the circuit breaker for at least one minute.
Step 2: Plug it back in and restart. The dishwasher should now respond to new commands.
FAQs Of How to reset Maytag dishwasher
How do I know if my Maytag dishwasher needs a reset?
If your dishwasher is unresponsive, shows blinking lights, stays in Demo Mode, or displays error codes, a reset may resolve these issues. Resetting often clears minor glitches and restores normal operation.
Does my Maytag dishwasher have a reset button?
No, Maytag dishwashers don’t have a dedicated reset button. You can reset them by following specific button sequences or unplugging them briefly.
How do I perform a factory reset on my Maytag dishwasher?
To perform a factory reset, open and close the dishwasher door, press the ‘Rinse’ button five times, and turn off Demo Mode by pressing the ‘Drain/Off’ button twice.
Why are my dishwasher lights blinking?
Blinking lights may signal a malfunction, Demo Mode activation, or an error. Resetting the control panel by pressing the ‘Rinse’ button five times and the ‘Drain/Off’ button twice often stops the blinking.
How do I clear an error code on my Maytag dishwasher?
First, confirm what the error code means to ensure it’s not a hardware issue. Then, unplug the dishwasher for 60 seconds to reset the control board and clear the code.
Is there a specific reset sequence for the Maytag 300 Series?
Yes, open the door, press the ‘Heated Dry’ and ‘Normal’ buttons twice in sequence, then close the door to start the reset.
How do I reset the Maytag Quiet Series 200 model?
Unplug the Quiet Series 200 dishwasher for at least one minute, then plug it back in. It should be ready to accept new commands.
